Vulcans™

• Choosing the correct Nose Pad

  Choosing the correct Nose pad is essential for maximum performance. Your Vulcans should sit close to your cheeks and brow (without touching), allowing air to flow whilst shielding your eyes from the wind.

  Nose Pad sizes

  • 4 Nose Pad sizes are included, numbered #1 to #4.

  • #1 is the smallest nose piece, suited for those with larger noses.

  • #4 is best suited to those with smaller noses and moves the frame further from your face.

  • #3 is fitted to your Vulcans as standard.

  Lens Fogging

  If your lens is fogging whilst exercising, there's not enough ventilation getting to the back side of the lens. Try moving up one Nose Pad size (#1 to #2, etc).

  Bouncing on Nose

  If your Vulcans are bouncing on your nose, try moving up one Nose Pad size (#1 to #2, etc) and pressing on to your nose when you put them on. The hydrophilic properties of the Nose Pad will keep your Vulcans in place when you sweat and work hard.

  Not enough wind coverage

  If you’re getting too much wind in your eyes, the frame is sitting too far from your face. Try moving down one Nose Pad size (#3 to #2, etc).

  Removing the Nose Pad

  To remove the Nose Pad, pull down on each side. Replace with the new Nose Pad best suited to your face shape. When attaching the new Nose Pad ensure the "SunGod" and number are on the outside, and the grip texture sits against your nose.

  Did we answer your question?

  Yes

  No
• Changing your Vulcans TF Lens
  Step 1: Remove the Lens from the Top Frame by pulling the Top Frame away at the mid-point above the “SunGod” engraving.

  Step 2: Remove the Nose Piece by pulling away from the Lens, first on one side then on the other.

  Step 3: Attach the Nose Piece to the new Lens. Push firmly to ensure it’s securely attached and seated centrally.

  Step 4: Attach the Lens into the Top Frame by first inserting both corners of the Lens into the pockets on the Top Frame near the hinge.

  Step 5: Work along the top of the Lens and firmly secure at the “SunGod” engraving.

  Step 6: For maximum performance use the provided 100% microfibre pouch to clean fingerprints and marks from your Lens.

  Did we answer your question?

  Yes

  No
• Changing your Vulcans FF Lens
  Step 1: Remove the Lens from the Top Frame by pulling the Top Frame away at the mid-point above the “SunGod” engraving.

  Step 2: Remove the Bottom Frame by unclipping from the holes on each side of the Lens.

  Step 3: Pull the Bottom Frame away at the nose.

  Step 4: Attach the Bottom Frame to the new Lens starting at the nose.

  Step 5: Work along the bottom of the Lens towards the outside, finally clipping the end of the Bottom Frame into the holes in the Lens.

  Step 6: Attach the Lens into the Top Frame by first inserting both corners of the Lens into the pockets on the Top Frame near the hinge.

  Step 7: Work along the top of the Lens and firmly secure at the “SunGod” engraving.

  Step 8: For maximum performance use the provided 100% microfibre pouch to clean fingerprints and marks from your Lens.

  Did we answer your question?

  Yes

  No
• Vulcans Top Frame to Full Frame (TF to FF) conversion
  Step 1: To change from Top Frame to Full Frame, you first need to remove the Lens from the Top Frame. To do this, pull the Top Frame away from the Lens at the mid-point above the “SunGod” engraving.

  Step 2: Remove the Nose Piece by pulling away from the Lens, first on one side then on the other.

  Step 3: Attach the Bottom Frame to the new Lens starting at the nose.

  Step 4: Work along the bottom of the Lens towards the outside, finally clipping the end of the Bottom Frame into the holes in the Lens.

  Step 5: Attach the Lens into the Top Frame by first inserting both corners of the Lens into the pockets on the Top Frame near the hinge.

  Step 6: Work along the top of the Lens and firmly secure at the “SunGod” engraving.

  Step 7: For maximum performance use the provided 100% microfibre pouch to clean fingerprints and marks from your Lens.

  Did we answer your question?

  Yes

  No
• Vulcans Full Frame to Top Frame (FF to TF) conversion
  Step 1: To change from Full Frame to Top Frame, you need to first remove the Lens from the Top Frame. To do this, pull the Top Frame away from the Lens at the mid-point above the ''SunGod'' engraving.

  Step 2: Remove the Bottom Frame by unclipping from the holes on each side of the lens. 

  Step 3: Pull the Bottom Frame away at the nose.

  Step 4: Attach the Nose Piece to the frame by pushing up onto the lens at the nose. 

  Step 5: Attach the Lens into the Top Frame by first inserting both corners of the Lens into the pockets on the Top Frame near the hinge.

  Step 6: Work along the top of the Lens and firmly secure at the “SunGod” engraving.

  Step 7: For maximum performance use the provided 100% microfibre pouch to clean fingerprints and marks from your Lens.

  Did we answer your question?

  Yes

  No
• How do I get replacement Ear Socks for my Pace Series Product?

  Lost your Ears Socks or have they come loose? Not to worry, this is 100% covered by our Lifetime Guarantee.

  Please complete the form found here to allow us to resolve the problem for you.

  In the box asking you to describe the issue, please let us know which colour Ear Socks you'd like.

  Did we answer your question?

  Yes

  No
• Troubleshooting

  Helmet Compatibility

  Vulcans have been designed to be compatible with all modern cycling helmet styles. Wear your Vulcans over your helmet strap.

  If the ends of the arms are touching your helmet at the back, try moving up one Nose Pad size (#1 to #2, etc).

  Wind Coverage

  If you’re getting too much wind in your eyes, the frame is sitting too far from your face. Try moving down one Nose Pad size (#3 to #2, etc).

  Lens Ventilation

  If your lens is fogging whilst exercising, there's not enough ventilation getting to the back side of the lens. Try moving up one Nose Pad size (#1 to #2, etc).

  Bouncing on Nose

  If your Vulcans are bouncing on your nose, try moving up one Nose Pad size (#1 to #2, etc) and pressing on to your nose when you put them on. The hydrophilic properties of the Nose Pad will keep your Vulcans in place when you sweat and work hard.

  Slipping down your Nose

  The Nose Pads on your Vulcans are made from a hydrophilic material (attracts water). As you start to sweat your Vulcans will grip tighter to your nose. If they are slipping down your face whilst exercising, try pressing more firmly on to your nose. You can also try moving up one Nose Pad size (#1 to #2, etc).

  If you've still got an unanswered question, please hit the button below, we'd be more than happy to help!

  Did we answer your question?

  Yes

  No
• Vulcans™ Lens Kits

  You can find replacement Lens Kits for all SunGod products, including Vulcans™, here.

  Did we answer your question?

  Yes

  No